Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Homeowner guide

What size furnace do I need for a Texas home?

Furnace size is measured in BTUs per hour, and in Schertz's mild climate the right answer is often smaller than you'd expect. Here's how sizing really works.

Quick answer

The only accurate way to size a furnace is a Manual J load calculation, which accounts for your home's insulation, windows, orientation and air leakage. Square-footage rules of thumb are rough at best. In Schertz (IECC climate zone 2A), many homes need noticeably less capacity than they have, and an oversized furnace short cycles and wears out faster.

BTUs, input and output

Furnaces are rated in BTUs per hour (BTU/h). Residential furnaces commonly range from about 40,000 to 120,000 BTU/h input. What heats your home is the output:

Output = input × AFUE

An 80,000 BTU/h input furnace at 80% AFUE delivers about 64,000 BTU/h of heat. The same input at 96% AFUE delivers about 76,800 BTU/h.

That's why a like-for-like swap from an 80% to a 95% furnace with the same input rating can actually make a system more oversized.

Why square-foot rules mislead

You'll see charts suggesting a certain number of BTUs per square foot by climate zone. They ignore what really drives heat loss:

  • Attic and wall insulation levels
  • Window type, size and which direction they face
  • Air leakage around doors, attic hatches and ducts
  • Ceiling height and layout
  • Duct location (ducts in a hot or cold attic lose heat)

Two 2,000 sq ft homes in Schertz, one from 1992 and one from 2022, can need very different furnace sizes.

The Manual J load calculation

Manual J is the industry-standard method from ACCA (Air Conditioning Contractors of America). A contractor measures your home and enters details into software that calculates heat loss on a local design-cold day. Then:

  • Manual S selects equipment that matches that load
  • Manual D checks the ducts can deliver the right airflow

Ask any contractor quoting a replacement: "Did you do a load calculation?" If the answer is "it's the same size as your old one," that's not sizing.

Problems with an oversized furnace

Short cycling

Frequent on/off cycles waste energy and wear out igniters, switches and the heat exchanger. See short cycling.

Uneven heat

The thermostat is satisfied before distant rooms warm up.

Noise and drafts

Too much airflow through ducts sized for less.

Higher upfront cost

You pay more for capacity you don't use.

Two-stage and modulating furnaces

Two-stage and modulating furnaces can run at lower output most of the time and ramp up only on the coldest days. In Schertz, where most winter days are mild, that means longer, quieter, more even cycles, and some protection if the sizing is slightly generous.

Upgraded your home? New windows, attic insulation or a radiant barrier since the furnace was installed? Your heating load has probably dropped. A new load calculation at replacement time can save money.

FAQ

Frequently asked questions

Don't see your question? Call (210) 898-9282.

What size furnace do I need for a 2,000 sq ft house?

It depends on insulation, windows and air leakage, so a Manual J calculation is the only accurate answer. In Schertz's mild climate, it's often less than older rules of thumb suggest.

Is it better to get a bigger furnace just in case?

No. Oversizing causes short cycling, uneven heat and faster wear. If you're worried about hard freezes, a two-stage furnace or dual-fuel system is a better hedge.

Does a contractor have to do a Manual J?

Building codes generally call for load calculations on new installations, and good contractors do them on replacements too. Ask for it.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate