Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Schertz, TX

Furnace & heating system installation in Schertz

Adding heat to a new space, converting from gas to a heat pump, or installing a complete new system? We design and install heating systems that are sized for your home, not guessed.

Installation goes beyond a one-for-one swap. It's for when you need a heating system designed for a space, or want to change how your home is heated.

Installation projects we handle

Complete new systems

New furnace and air handler with matched cooling equipment, thermostat and ductwork for homes without a working system.

Gas to heat pump conversions

Replacing a gas furnace and AC with an all-electric heat pump that handles both heating and cooling.

Dual-fuel systems

A heat pump for mild weather plus a gas furnace that takes over in hard freezes. Efficient most of the year, strong in a storm.

Additions and conversions

Heating for room additions, garage conversions and finished attics, by extending ducts or adding a ductless mini-split.

Relocating equipment

Moving a furnace out of the attic into a closet or garage for easier service, when the layout allows.

Efficiency upgrades

Moving from 80% to 95% AFUE, or from single-stage to two-stage or modulating heat for steadier comfort.

Design comes first: load calculations and ducts

The most common installation mistake in Texas is equipment that's too big. Contractors often size by square footage alone and round up. The result is a furnace that short cycles, wears out early and leaves some rooms hot and others cold.

  • Manual J calculates how much heat your home actually loses on a design cold day, based on insulation, windows, orientation and air leakage.
  • Manual S selects equipment that matches that load.
  • Manual D sizes the ductwork so each room gets the right airflow. Many attic ducts in older Schertz homes are undersized or leaky, and a new furnace can't fix bad ducts.

Schertz sits in IECC climate zone 2A, with a short heating season and occasional hard freezes. A proper load calculation often shows a home needs a smaller furnace than the one it has, which saves money upfront and runs more evenly. Read what size furnace do I need.

The installation process

  1. Home visit and measurements. Square footage, insulation, windows, duct condition and the electrical panel (important for heat pumps and heat strips).
  2. Written proposal. Equipment options with efficiency ratings, warranty terms and an itemized price.
  3. Permits. We pull any required mechanical permit and schedule inspections.
  4. Installation. Equipment, gas piping, venting, condensate drain, electrical and duct connections installed to code and manufacturer instructions.
  5. Commissioning. We measure gas pressure, temperature rise, static pressure and airflow, then adjust until the system runs within spec.
  6. Walkthrough. Thermostat setup, filter location and size, and warranty registration.

Converting to a heat pump? Heat strips draw a lot of current, so your electrical panel needs enough capacity. We check this during the first visit so there are no surprises on installation day.

Heating system installation cost in Schertz

Typical installation costsParts and labor, Schertz / San Antonio area, 2026 estimates. You get an exact written price before work begins.
Item Typical cost Notes
Gas furnace installation $3,500 – $8,500 Efficiency and location drive the range
Heat pump system (heat + cool) $7,000 – $15,000+ Size, efficiency (SEER2/HSPF2) and brand
Dual-fuel system $9,000 – $18,000+ Heat pump plus gas furnace
Ductless mini-split (one zone) $3,000 – $6,500 Additions and converted spaces
Ductwork replacement $2,500 – $8,000 Depends on size and attic access
FAQ

Furnace Installation FAQs

Don't see your question? Call (210) 898-9282.

What's the difference between furnace replacement and installation?

Replacement swaps an existing furnace for a new one in the same place. Installation covers new or changed systems: new homes or additions, conversions to a heat pump or dual fuel, relocating equipment, or adding ductwork.

Do I need a permit for a new furnace in Schertz?

Furnace installation generally requires a mechanical permit and inspection. A licensed contractor should pull the permit. If one suggests skipping it, that's a red flag.

Is a heat pump enough for a Texas freeze?

A properly sized heat pump with electric heat strips can keep a Schertz home warm through a hard freeze, though the strips use a lot of electricity. Dual-fuel systems use gas for those coldest hours instead.

Should I replace my ductwork when installing a new system?

Not always. We test static pressure and inspect the ducts. If they're the right size and in good shape, they can stay. Leaky, crushed or undersized attic ducts should be fixed, or the new system won't deliver its rated performance.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate