Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Schertz, TX

Heating repair in Schertz, TX

Not sure if it's the furnace, the heat pump or the thermostat? We diagnose and repair every type of home heating system in Schertz, and you approve the price before we start.

"My heat isn't working" can mean a dozen different problems. Heating repair starts by finding out which one, and that depends on what kind of system heats your home.

Heating problems we fix every week in Schertz

No heat at all

Failed igniter, tripped breaker, blown control fuse, bad thermostat or a gas supply problem.

Cold or lukewarm air

Dirty flame sensor, overheating shutdown, heat pump stuck in defrost or failed heat strips.

Heat comes on, then quits

Short cycling from a clogged filter, a weak flame sensor or a limit switch tripping.

Uneven heat between rooms

Airflow restrictions, disconnected attic ducts, a weak blower or an undersized system.

Noisy operation

Squealing blower bearings, a rattling inducer motor or a boom from delayed ignition.

System runs nonstop

Low refrigerant in a heat pump, a failing thermostat, or heat loss the system can't keep up with.

Gas furnace, electric furnace or heat pump: why it matters

Schertz has a mix of all three. Older neighborhoods mostly have gas furnaces. Many newer subdivisions use heat pumps with electric heat strips as backup. The same symptom points to very different causes:

  • Gas furnace blowing cold air usually means the burners aren't lighting or are shutting off early (igniter, flame sensor, gas valve).
  • Heat pump blowing cool air may be normal during a defrost cycle, or it may mean low refrigerant, a failed reversing valve or heat strips that aren't kicking in.
  • Electric furnace with weak heat often has one or more burned-out heating elements or a failed sequencer.

Our technicians work on all three, so you don't need to know your system type before calling. If you'd like to find out, check the thermostat: "AUX" or "EM heat" settings mean a heat pump. Our post on em heat vs heat explains those settings.

How we diagnose a heating problem

  1. Safety first. We check for gas leaks and carbon monoxide before working on any fuel-burning system.
  2. Confirm the call for heat. Thermostat settings, wiring and power to the furnace or air handler.
  3. Read the system. Error codes on the control board, the ignition sequence, flame quality, refrigerant pressures on heat pumps, and amperage on electric elements.
  4. Check airflow. Filter, blower, return and supply. Restricted airflow causes more shutdowns than any failed part.
  5. Explain and quote. You hear what failed, why, and the exact price to fix it before any work begins.

Try these first: confirm the thermostat is on HEAT with fresh batteries, check the furnace breaker and the switch on the unit, and replace a dirty filter. If heat doesn't return within 15 minutes, call us. Don't keep resetting a furnace that locks out.

Repair or replacement?

Most heating problems are fixed with a single part. Replacement only comes into the conversation when the system is old and the repair is expensive, or when there's a safety issue like a cracked heat exchanger. Try the $5,000 rule calculator on our furnace repair page, or read the repair-or-replace guide.

Heating repair cost in Schertz

Typical ranges for the most common heating repairs across gas, electric and heat pump systems:

Typical heating repair costsParts and labor, Schertz / San Antonio area, 2026 estimates. You get an exact written price before work begins.
Item Typical cost Notes
Diagnostic / service call $80 – $200 Often credited toward the repair
Thermostat repair or replacement $120 – $450 Smart thermostats at the higher end
Igniter or flame sensor (gas) $90 – $450 Most common gas furnace repairs
Heating element or sequencer (electric) $200 – $600 Per element; heat strips vary by kW
Capacitor or contactor (heat pump) $150 – $400 Common heat pump start-up failures
Blower motor $450 – $1,800 Variable-speed ECM motors cost more
FAQ

Heating Repair FAQs

Don't see your question? Call (210) 898-9282.

What's the difference between heating repair and furnace repair?

Furnace repair is one type of heating repair. Heating repair covers any system that heats your home, including heat pumps and electric air handlers with heat strips. If you're not sure what you have, book heating repair and the technician will identify it.

Why is my heat pump blowing cold air in winter?

During defrost, a heat pump briefly runs in cooling mode to melt ice off the outdoor coil, and the air can feel cool for a few minutes. That's normal. If it lasts longer than about 15 minutes, the heat strips may not be engaging or the system may be low on refrigerant. Both need a technician.

Can you repair any brand of heating system?

Yes: Lennox, Trane, Carrier, Goodman, Rheem, Ruud, Amana, American Standard, Bryant and more. See furnace brands we service.

Is it safe to keep running my furnace if it's making a strange noise?

A new squeal or rattle usually isn't an emergency, but a loud bang at start-up (delayed ignition) or any gas smell is. Turn the system off and call. Running a failing blower motor can also overheat the furnace and cause more damage.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate