Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Schertz, Texas · Furnace & heating repair

Furnace repair in Schertz, TX, done right the first time.

Gas furnaces, electric furnaces, attic units and heat pumps, every brand. A licensed technician finds the real cause and you approve the price in writing before any work begins.

Illustration of a Schertz home cutaway with an attic furnace sending warm air to the rooms below on a cold day
Written price firstYou approve before work
CO safety checkOn every heating call
24/7Phones answered nights, weekends and holidays
TDLRTexas-licensed HVAC technicians
UpfrontWritten price before any repair
8+Major furnace brands repaired
We repairLennoxTraneCarrierGoodmanRheemRuudAmanaAmerican Standard
02Book

Book a technician in about a minute

Tell us what's going on. We'll call you back to confirm a time, usually within the hour during the day.

  1. Send the form or callDescribe the symptoms in your own words.
  2. Get an arrival windowOften same-day for no-heat calls.
  3. Approve the price on siteNo work starts until you say yes.

Book a technician

Takes about a minute. We call back to confirm your arrival window.

No obligation. Smell gas? Leave the home and call 911 or your gas utility from outside.

03Warning signs

Six signs your furnace needs repair

Most furnaces give warning before they fail. Catching these early usually means a smaller bill and no cold night.

  1. Blowing cold or lukewarm airOften a failed igniter, a dirty flame sensor, a gas supply problem or an overheating shutdown.
  2. Turning on and off constantlyShort cycling points to a clogged filter, a faulty flame sensor, a bad limit switch or an oversized unit.
  3. Banging, squealing or rattlingDelayed ignition, worn blower bearings or a loose panel need attention before they get worse.
  4. A burning smell that lingersA short dusty smell at first start-up is normal. A smell that stays can mean an overheating motor or wiring.
  5. Water around the furnaceHigh-efficiency and attic furnaces make condensate. A clogged drain can overflow into your ceiling.
  6. Higher energy billsA furnace that runs longer for the same heat is losing efficiency and may have a failing part.

Want to try the safe checks first, like the thermostat, filter and breaker? See the furnace troubleshooting blog.

04Inside the furnace

Inside your furnace: what fails, and why

Pick a part, from the strip or the numbered dots, to see the symptoms it causes, whether you can check it yourself, and what the repair typically costs in Schertz.

Cutaway diagram of a gas furnace showing the thermostat, filter, igniter, flame sensor, inducer motor, heat exchanger, blower motor and condensate drain Warm air to home Flue Gas line Cool return air
Part 1 of 8

Thermostat

Tells the furnace when to heat. Many "broken furnace" calls turn out to be dead batteries or a wrong setting.

Furnace not turning on? →
SymptomsFurnace never starts; room temperature doesn't match the setting.
Check it yourself?Check batteries, set it to HEAT and raise the set point 3–5 degrees.
Typical cost$120 – $450 to repair or replace
Part 2 of 8

Air filter

Cleans return air before it reaches the blower. A clogged filter starves the furnace of airflow.

Furnace filter guide →
SymptomsWeak airflow, short cycling, overheating and the limit switch tripping.
Check it yourself?Yes. Replace it every 1–3 months, more often during cedar pollen season.
Typical cost$10 – $40 for a new filter
Part 3 of 8

Hot surface igniter

Glows red-hot to light the burners. It's brittle and often cracks on the first cold start of the season.

Igniter replacement →
SymptomsInducer runs and clicks, but the burners never light.
Check it yourself?No. It's fragile and sits next to the gas burners, so it needs a technician.
Typical cost$150 – $450 installed
Part 4 of 8

Flame sensor

Confirms a flame is present. If it's coated with residue, the furnace shuts off the gas for safety.

Flame sensor repair →
SymptomsBurners light, then shut off after 3–10 seconds and retry.
Check it yourself?Cleaning is possible for confident homeowners with the power and gas off. Otherwise call a technician.
Typical cost$90 – $250
Part 5 of 8

Inducer motor

Pulls combustion gases through the heat exchanger and out the flue before ignition is allowed.

Inducer motor replacement →
SymptomsLoud humming or whining, or a pressure-switch error code before ignition.
Check it yourself?No. Motor replacement needs a technician.
Typical cost$450 – $1,500
Part 6 of 8

Heat exchanger

Separates the flame from the air you breathe. A crack can let carbon monoxide into your home.

Heat exchanger repair →
SymptomsSoot, rust, a yellow or wavy flame, or a CO alarm.
Check it yourself?No. A suspected crack is a safety issue. Shut the furnace off and call.
Typical cost$1,500 – $4,000+ (often the point to replace)
Part 7 of 8

Blower motor

Pushes heated air through your ducts. Variable-speed (ECM) motors are quieter but cost more to replace.

Blower motor repair →
SymptomsNo airflow from vents, squealing, or a blower that hums but won't spin.
Check it yourself?No. Capacitor and motor work involves high voltage.
Typical cost$450 – $1,800 (capacitor alone: $120 – $350)
Part 8 of 8

Condensate drain

High-efficiency furnaces make water. The drain line and trap carry it away, and they clog easily in attics.

Condensate drain repair →
SymptomsWater on the floor or a stained ceiling under an attic unit, plus pressure-switch lockouts.
Check it yourself?You can check for visible clogs. Flushing traps and replacing pumps is technician work.
Typical cost$120 – $400
05How it works

What happens when you call us

Five steps, the same on every call, whether it's a $90 flame sensor or a full replacement.

Start with a call
  1. Call or book online

    Describe the symptoms and get an arrival window, often the same day.

  2. Safety check first

    We test for gas leaks and carbon monoxide before working on the furnace.

  3. Find the real cause

    Ignition, airflow, gas pressure, safety switches and error codes, not guesswork.

  4. Approve the price

    You see the repair options and the exact price in writing. No pressure to replace.

  5. Repair and verify

    We fix it, then run full heating cycles to confirm it stays on.

06Pricing

What furnace repair costs in Schertz

Most repairs cost $150 to $650. Use these typical ranges to judge any quote you receive.

Diagnostic / service call$80 – $200Often credited toward the repair
Flame sensor clean or replace$90 – $250Furnace lights, then shuts off
Hot surface igniter$150 – $450Most common first-start failure
Pressure or limit switch$150 – $450Often an airflow or drain issue
Blower capacitor$120 – $350Blower hums but won't spin
Control board$350 – $900Varies by brand and model
Inducer motor$450 – $1,500Whining before ignition
Blower motor$450 – $1,800ECM motors cost more
Heat exchanger$1,500 – $4,000+Often where replacement wins

Parts and labor, Schertz / San Antonio area, 2026 estimates. Attic installs can take longer. You always get an exact written price first. Full cost guide →

Repair or replace? Try the $5,000 rule

My furnace is years old, and the repair quote is $.

8,400Age × repair cost
Replacement is worth a serious look

Above 5,000, the money spent on repairs often goes further toward a new, more efficient furnace. Ask for both prices before deciding.

Full guide
07Local knowledge

Why Schertz furnaces fail differently

Furnaces here sit idle eight or nine months, then have to work hard the moment a cold front arrives.

Knowing the local patterns (attic installs, heat pumps in newer subdivisions, the first-freeze rush) helps us diagnose faster and recommend repairs that last.

Attic heat ages parts

Texas attics can pass 130°F in summer, wearing out capacitors, boards and wiring. Clogged attic drains overflow into ceilings. See attic furnace repair.

First cold front, first failures

Igniters crack and dusty flame sensors fail on the first start of the season. A fall tune-up prevents most of them.

Hard freezes test every system

Winter Storm Uri in February 2021 kept furnaces running nonstop for days. See the freeze prep guide.

Cedar pollen clogs filters

Mountain cedar season (about December–February) loads filters right in peak heating months. See the filter guide.

Zone 2AIECC climate zone for Schertz: hot-humid, short heating seasons
Nov–DecTypical first freeze in the San Antonio area
130°F+Summer attic temperatures around attic furnaces
15–20 yrsTypical gas furnace lifespan with yearly service

Smell gas or hear a CO alarm? Do this first.

  1. Leave the home right away with everyone, including pets.
  2. Don't flip switches, use phones or start a car inside or in an attached garage.
  3. From outside, call 911 or your natural gas utility's emergency line.
  4. Stay out until responders say it's safe, then call us to inspect the furnace.

Carbon monoxide has no smell. Keep working CO alarms near bedrooms and on every level. See our carbon monoxide guide.

08Service area

Do we serve your address?

Enter your ZIP code, or browse Schertz neighborhoods and nearby cities below.

All service areas

Schematic map of Schertz, Texas and nearby cities served: Garden Ridge, New Braunfels, Selma, Cibolo, Universal City, Live Oak, JBSA-Randolph and Converse I-35 Loop 1604 FM 78 Schertz Garden Ridge New Braunfels Selma Cibolo Universal City Live Oak JBSA-Randolph Converse
Schematic map, not to scale
09Our promise

What every repair visit includes

The same standards on every call. If a technician skips any of these, tell us.

How we work

Every visit includesSchertz, TX
  • Full system diagnosisNot just the obvious symptom
  • Carbon monoxide checkOn every heating call
  • Written price firstYou approve before work starts
  • Filter & airflow checkThe cause of most overheating
  • Full-cycle test runConfirmed working before we leave
  • Clean work areaShoe covers, drop cloths, old parts removed
Surprise charges$0
10FAQ

Questions Schertz homeowners ask us

Don't see yours? Call (210) 898-9282.

How much does furnace repair cost in Schertz, TX?

Most common furnace repairs in the Schertz and San Antonio area fall between about $150 and $650, parts and labor included. Cleaning a flame sensor sits at the low end. Blower motors, inducer motors and control boards cost more. A failed heat exchanger can run into the thousands, which is when replacement often makes more sense. We give you the exact price before any work starts. See the furnace repair cost guide.

Do you offer 24/7 emergency furnace repair in Schertz?

Yes. Cold fronts reach Schertz fast, and a furnace that quits overnight can't wait until Monday. Call (210) 898-9282 any time for emergency furnace repair. If you smell gas, leave the house first and call 911 or your gas utility from outside.

Should I repair or replace my old furnace?

Start with the $5,000 rule: multiply the furnace's age by the repair cost. Above 5,000, replacement deserves a serious look. A 16-year-old furnace with a $400 repair scores 6,400. Safety (a cracked heat exchanger), frequent breakdowns and energy bills matter too. Try the calculator above or read our repair-or-replace guide.

Why does my furnace smell like burning when I first turn it on?

After months of Texas heat, dust settles on the burners and heat exchanger, and the first heating cycles burn it off. A dusty smell for up to an hour is normal. A smell that lasts longer, or smells electrical or like hot plastic, is not. Turn the system off and see our burning smell guide.

How often should a furnace be serviced in Texas?

Once a year, ideally in the fall before the first cold front. Schertz furnaces sit idle most of the year, so the first start-up is when igniters and flame sensors fail. A furnace tune-up catches those problems early and includes a carbon monoxide check.

Do you repair heat pumps and electric furnaces too?

Yes. Many newer homes in Schertz and Cibolo heat with a heat pump backed by electric heat strips, while others have gas furnaces. We repair all of them, from every major brand. If your thermostat shows "EM heat" or "AUX heat", read em heat vs heat.

What areas near Schertz do you serve?

All of Schertz (ZIP 78154) plus Cibolo, Universal City, Converse, Selma, Garden Ridge, Live Oak and homes near JBSA-Randolph. Check your ZIP above or see the service areas page.

Furnace down? Let's get your heat back today.

(210) 898-9282

Licensed furnace repair in Schertz, TX · Written price before work · 24/7

Or book online
Call Now Free Estimate