Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Schertz, TX · Furnace component repair

Furnace parts repair, diagnosed before replaced.

Igniters, flame sensors, motors, control boards, gas valves and more. We test to confirm which part failed, show you the price in writing, and carry the most common parts on every truck.

  • Exact-spec or OEM parts
  • Written price before work
  • CO check on every repair
10Furnace components with in-depth repair guides
$90–$450Typical installed cost of the most common part repairs
All brandsLennox, Trane, Carrier, Goodman, Rheem and more
24/7Emergency part repairs, nights and weekends
02How it works

How a gas furnace works, part by part

Every heating cycle depends on these parts working in order: thermostat, inducer, pressure switch, igniter, gas valve, flame sensor, then blower. Pick a part to explore.

Cutaway diagram of a gas furnace showing the thermostat, filter, igniter, flame sensor, inducer motor, heat exchanger, blower motor and condensate drain Warm air to home Flue Gas line Cool return air
Part 1 of 8

Thermostat

Tells the furnace when to heat. Many "broken furnace" calls turn out to be dead batteries or a wrong setting.

Furnace not turning on? →
SymptomsFurnace never starts; room temperature doesn't match the setting.
Check it yourself?Check batteries, set it to HEAT and raise the set point 3–5 degrees.
Typical cost$120 – $450 to repair or replace
Part 2 of 8

Air filter

Cleans return air before it reaches the blower. A clogged filter starves the furnace of airflow.

Furnace filter guide →
SymptomsWeak airflow, short cycling, overheating and the limit switch tripping.
Check it yourself?Yes. Replace it every 1–3 months, more often during cedar pollen season.
Typical cost$10 – $40 for a new filter
Part 3 of 8

Hot surface igniter

Glows red-hot to light the burners. It's brittle and often cracks on the first cold start of the season.

Igniter replacement →
SymptomsInducer runs and clicks, but the burners never light.
Check it yourself?No. It's fragile and sits next to the gas burners, so it needs a technician.
Typical cost$150 – $450 installed
Part 4 of 8

Flame sensor

Confirms a flame is present. If it's coated with residue, the furnace shuts off the gas for safety.

Flame sensor repair →
SymptomsBurners light, then shut off after 3–10 seconds and retry.
Check it yourself?Cleaning is possible for confident homeowners with the power and gas off. Otherwise call a technician.
Typical cost$90 – $250
Part 5 of 8

Inducer motor

Pulls combustion gases through the heat exchanger and out the flue before ignition is allowed.

Inducer motor replacement →
SymptomsLoud humming or whining, or a pressure-switch error code before ignition.
Check it yourself?No. Motor replacement needs a technician.
Typical cost$450 – $1,500
Part 6 of 8

Heat exchanger

Separates the flame from the air you breathe. A crack can let carbon monoxide into your home.

Heat exchanger repair →
SymptomsSoot, rust, a yellow or wavy flame, or a CO alarm.
Check it yourself?No. A suspected crack is a safety issue. Shut the furnace off and call.
Typical cost$1,500 – $4,000+ (often the point to replace)
Part 7 of 8

Blower motor

Pushes heated air through your ducts. Variable-speed (ECM) motors are quieter but cost more to replace.

Blower motor repair →
SymptomsNo airflow from vents, squealing, or a blower that hums but won't spin.
Check it yourself?No. Capacitor and motor work involves high voltage.
Typical cost$450 – $1,800 (capacitor alone: $120 – $350)
Part 8 of 8

Condensate drain

High-efficiency furnaces make water. The drain line and trap carry it away, and they clog easily in attics.

Condensate drain repair →
SymptomsWater on the floor or a stained ceiling under an attic unit, plus pressure-switch lockouts.
Check it yourself?You can check for visible clogs. Flushing traps and replacing pumps is technician work.
Typical cost$120 – $400
04Safety

What you can check, and what needs a technician

Some checks are safe and solve real problems. Others involve gas, 120–240 volt circuits or carbon monoxide risk and belong to a licensed professional.

Safe for homeowners

Try these before you call

  • Air filterChange every 1–3 months, monthly in cedar season
  • Thermostat batteries and settingsHEAT mode, set point 3–5° above room temperature
  • Furnace switch and breakerReset once; repeated trips need a technician
  • Visible condensate line clogsLook and check the pan; leave traps to a pro
  • Flame sensor cleaning (with care)Power and gas off; call if you're unsure

Call a licensed technician

Gas, electrical or CO risk

  • Igniters, motors and capacitorsFragile parts and high-voltage circuits
  • Control boards and wiringDiagnosis needs meters and wiring diagrams
  • Gas valve and gas pipingLeak testing and pressure set with a manometer
  • Heat exchanger and flueCarbon monoxide risk; needs combustion testing
  • Safety switchesNever bypass a pressure, limit or rollout switch
05Parts quality

OEM vs universal parts: how we choose

We tell you which type we're using, and why, before the repair. The goal is the right part at a fair price, without risking your warranty.

Universal, exact-spec

When it makes sense

Designed to fit many furnaces, matched to the original's ratings. Usually faster to get and lower cost.

  • Hot surface igniters
  • Capacitors and many motors
  • Pressure and limit switches (exact rating)
Original manufacturer (OEM)

When we insist on it

Made for your exact model. The safest choice for complex electronics and warranty-covered repairs.

  • Control boards, especially communicating systems
  • Some gas valves and ECM blower motors
  • Any part under an active manufacturer warranty

Prices shown on this site are 2026 estimates for the Schertz / San Antonio area, including parts and labor. See the full furnace repair cost guide.

FAQ

Furnace parts FAQs

Don't see your question? Call (210) 898-9282.

What is the most common furnace part to fail?

In Schertz, the hot surface igniter and the flame sensor top the list, especially on the first cold day of the season. Both are relatively inexpensive repairs. See igniter replacement and flame sensor repair.

Can I buy a furnace part and have you install it?

We generally supply parts ourselves so we can match the exact specifications and stand behind the repair. Online parts are sometimes the wrong rating or counterfeit, which can cause repeat failures or void a warranty.

Are furnace parts covered by warranty?

Many manufacturers cover parts for 5–10 years, often longer if the furnace was registered after installation. Labor is usually not covered. Give us your serial number and we'll help check. See furnace brands we service.

When is a part repair not worth it?

When the part is a heat exchanger, or when an expensive repair on an old furnace fails the $5,000 rule (age × repair cost). See repair or replace.

Know which part failed? We can fix it today.

Common parts are on our trucks, and every repair starts with a written price. Call any time, or book online and we'll call you back.

24/7 furnace repair (210) 898-9282 Book online instead
Call Now Free Estimate