Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Schertz, TX · Furnace parts

Furnace control board replacement in Schertz

The control board is your furnace's brain. When it fails, the furnace may do nothing at all, run the blower nonstop, or behave erratically. But many "bad board" calls turn out to be something simpler.

What the control board does

The integrated furnace control board runs the heating sequence. It reads the thermostat, starts the inducer, checks the safety switches, powers the igniter, opens the gas valve, verifies the flame and runs the blower at the right speed. It also stores and flashes diagnostic codes on a small LED when something goes wrong.

Signs of a failing control board

  • No response at all, with no LED light, even though the furnace has power
  • The blower runs constantly and won't shut off
  • The furnace starts the sequence out of order or stops at random steps
  • Clicking relays with no action, or burned and discolored spots on the board
  • Codes that don't match what's actually happening

Check these before replacing a board

Control boards are expensive, and they're often replaced unnecessarily. A good diagnosis rules these out first:

  1. The low-voltage fuse. Most boards have a small 3A or 5A automotive-style fuse. A shorted thermostat wire (often nicked during remodeling or by pests) blows it. Replacing the fuse without fixing the short just blows it again.
  2. Power and the door switch. Furnaces have a safety switch that cuts power when the panel is off. A loose panel or failed switch looks like a dead board.
  3. The transformer that supplies 24 volts to the board and thermostat.
  4. The thermostat and its wiring. A failed thermostat can't call for heat.
  5. The part the code points to. A board flashing a pressure switch code is usually reporting a real problem elsewhere, not failing itself.

What damages control boards in Schertz

  • Power surges and lightning from Central Texas thunderstorms. A whole-home or HVAC surge protector is inexpensive insurance.
  • Attic heat. Boards in attic furnaces endure summer temperatures that age electronic parts faster.
  • Water. Condensate leaks or a dripping AC coil above the furnace can short a board.
  • Shorted wiring that overloads relays.

After a storm: if your furnace stops working right after a power outage or lightning, turn the system off at the thermostat, then cycle the furnace switch. If it doesn't come back, the board or transformer may be damaged, so call for service rather than resetting repeatedly.

OEM or universal board?

Universal replacement boards work well on many standard single-stage furnaces. Two-stage, variable-speed and communicating systems (such as some Carrier Infinity, Lennox iComfort and Trane ComfortLink models) generally need the original manufacturer's board. The original may also be covered under the parts warranty.

Control board replacement cost

Typical control board costs in SchertzParts and labor, Schertz / San Antonio area, 2026 estimates. You get an exact written price before work begins.
Item Typical cost Notes
Low-voltage fuse and short repair $100 – $250 Fix the wiring short, replace the fuse
Transformer replacement $150 – $350 No 24V power to the board
Universal control board, installed $350 – $650 Standard single-stage furnaces
OEM control board, installed $500 – $900+ Two-stage, variable-speed, communicating
HVAC surge protector $150 – $350 Protects the board and motors
FAQ

Control Board Replacement FAQs

Don't see your question? Call (210) 898-9282.

How do I know if my furnace control board is bad?

No LED light with power confirmed, a blower that won't stop, or a sequence that stops at random points can all indicate a bad board. Because fuses, transformers and wiring cause similar symptoms, testing is needed before replacing it.

Can a power outage damage a furnace control board?

The outage itself usually doesn't, but the surge when power returns, or a lightning strike, can. Surge protection helps.

Is it worth replacing a control board on an old furnace?

On a 15–20-year-old furnace, an expensive OEM board may fail the $5,000 rule. See repair or replace.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate