Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Furnace troubleshooting

Furnace blinking light codes: how to read them

That small blinking light behind your furnace's sight window is a built-in diagnostic tool. Reading it correctly can save time, and sometimes a service call.

Quick answer

Count the flashes in a pattern (for example, 3 flashes, a pause, then repeat), then match the number to the code chart printed inside your furnace's door panel. Codes differ by brand and model, so always use your furnace's own chart. Common categories are pressure switch, limit (overheating), ignition failure and rollout.

How to read the code

  1. Don't remove the panel yet. Most furnaces show the LED through a small window in the lower door. Removing the door cuts power through a safety switch and may clear the code.
  2. Watch a few full cycles. Count the flashes between pauses. Some codes use long and short flashes, or two colors.
  3. Find the code chart. It's usually a sticker on the inside of the door or on the furnace cabinet. Your owner's manual has it too.
  4. Note the code before resetting. Many boards clear it after a power cycle.

Why codes differ: "3 flashes" means one thing on a Goodman board and something else on a Carrier or Lennox board. Never rely on a generic list for your exact number. Use it only to understand the category.

Common code categories (all brands)

Code type What it usually means What to do
Steady on or slow regular blink Normal operation or standby on many boards Nothing; furnace is ready
Rapid flashing Often flame sensed with no call for heat, or reversed polarity, depending on brand Call; may be a wiring or gas valve issue
Pressure switch code Switch didn't close: blocked vent, clogged condensate trap, weak inducer Check the drain pan, then call
Limit circuit open Overheating: dirty filter, blocked vents, blower problem Replace the filter and open the vents
Ignition failure / lockout Burners didn't light or stay lit: igniter, flame sensor, gas supply Reset once; call if it repeats
Flame rollout Flames escaped the burner area: blocked flue or heat exchanger issue Turn off and call. Don't reset repeatedly
No light at all No power to the board: breaker, switch, door switch, fuse or transformer Check the breaker, switch and door panel

The codes we see most in Schertz

Pressure switch codes

Very common with high-efficiency furnaces in attics, where condensate traps and drains clog. The switch is usually fine. The water or blockage behind it is the problem. See pressure switch repair and condensate drain repair.

Ignition lockout codes

Spike on the first cold day of the season, when weakened igniters crack and dusty flame sensors fail. See igniter and flame sensor.

Limit codes

Usually a clogged filter, especially during cedar pollen season. Try a new filter first. See furnace keeps shutting off.

Smart thermostats and communicating systems

Some premium systems (for example communicating Carrier, Lennox and Trane models) show alerts on the thermostat screen instead of, or in addition to, the board LED. Write down the full message or alert number when you call.

When to call

Call right away for rollout codes, any code with a gas smell, or a code that returns after one reset. Tell us the brand, model (from the data plate) and flash pattern, and we can often bring the right part on the first visit.

FAQ

Frequently asked questions

Don't see your question? Call (210) 898-9282.

Where is the code chart for my furnace?

Usually on a sticker inside the furnace's front door panel or on the side of the cabinet. It's also in the installation or owner's manual, which manufacturers often post online by model number.

What does a solid green or steady light mean?

On many boards a steady or slowly blinking light means normal operation or standby. Check your furnace's chart to confirm.

Will turning the power off clear the code?

On many furnaces, yes. Count and record the flash pattern before you reset or remove the panel.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate