Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Schertz, TX · Furnace parts

Furnace flue & venting repair in Schertz

Your furnace's vent pipe carries carbon monoxide and other exhaust out of your home. A blocked, disconnected or poorly sloped vent can cause lockouts, or put exhaust where it shouldn't be.

CO alarm, exhaust smell, or a vent pipe that's fallen apart in the attic? Turn the furnace off. If anyone feels ill or an alarm is sounding, get outside and call 911.

Two kinds of furnace venting

80% furnaces: metal flue

Hot exhaust rises through double-wall metal pipe (B-vent) and out a roof cap. It must slope upward and keep required clearances from wood and insulation.

90%+ furnaces: PVC pipes

Cooler exhaust is pushed out through plastic pipe, often with a second pipe bringing in combustion air. Exhaust pipes slope back toward the furnace so condensate drains.

Common venting problems in Schertz homes

  • Disconnected or separated joints in the attic. Pipes get bumped during other attic work or sag over time. A disconnected flue can vent exhaust into the attic.
  • Nests and debris. Birds and wasps build in vent terminations, especially PVC pipes on sidewalls and roofs after the furnace sits idle all summer.
  • Improper slope. PVC exhaust sloped the wrong way traps condensate, causing gurgling and pressure-switch lockouts.
  • Roof work damage. Roofers replacing shingles after hailstorms sometimes damage or reconnect flue caps and roof jacks incorrectly.
  • Rusted or deteriorated metal flue on older systems.
  • Shared flue issues when a gas water heater vents into the same flue, especially after one appliance is replaced.

Signs of a venting problem

  • Pressure-switch error codes or a tripped rollout switch
  • An exhaust or "chemical" smell when the furnace runs
  • Gurgling or water sounds in the PVC pipe
  • Rust, soot or water stains around the flue where it leaves the furnace
  • A carbon monoxide alarm

What we inspect and repair

  1. Trace the full vent run from furnace to termination, including the attic and the roof cap.
  2. Check joints, supports, slope and clearances against the manufacturer's installation instructions and code.
  3. Clear blockages at terminations and install screens or guards where appropriate.
  4. Measure draft and run a combustion test to confirm exhaust is leaving the home properly.
  5. Repair or replace damaged sections with the correct material for your furnace.

If we find venting problems along with a damaged heat exchanger or chronic rollout trips, we'll explain how they're connected.

Flue and venting repair cost

Typical venting repair costs in SchertzParts and labor, Schertz / San Antonio area, 2026 estimates. You get an exact written price before work begins.
Item Typical cost Notes
Vent termination clearing $150 – $300 Nests and debris, with guard install
Reconnect / secure attic flue joints $150 – $400 Includes draft and CO test
Re-slope or replace PVC venting $300 – $800 Depends on length and access
Metal flue section replacement $300 – $800 Rusted or damaged B-vent
FAQ

Flue & Venting Repair FAQs

Don't see your question? Call (210) 898-9282.

Can a disconnected furnace flue cause carbon monoxide?

Yes. A disconnected or broken flue can release exhaust, including carbon monoxide, into the attic or living space. Turn the furnace off and have it repaired before using it again.

Why is there water in my furnace vent pipe?

On high-efficiency furnaces, some condensate in the PVC exhaust is normal, but it should drain back to the furnace. Gurgling or standing water usually means the pipe is sloped wrong or the drain is clogged.

Should my furnace vent be checked after a roof replacement?

It's a good idea. Flue caps and roof jacks are disturbed during roofing, and a quick check confirms everything is reconnected and sealed correctly.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate