Technicians on call now · Schertz, Cibolo & Universal City Furnace & heating repair · Written price before work
Schertz, TX · Furnace parts

Furnace pressure & limit switch repair in Schertz

Safety switches stop your furnace when something is wrong. When one trips, the switch is often working perfectly, and the real job is finding what made it trip.

The safety switches in your furnace

Pressure switch

Confirms the inducer has created a safe draft before ignition is allowed. A rubber tube connects it to the inducer or the condensate collector box.

High limit switch

Shuts off the burners if the air around the heat exchanger gets too hot, usually because air isn't moving through the furnace fast enough.

Rollout switch

Trips if flames roll out of the burner area. Usually it must be reset by hand, and it signals a serious problem like a blocked flue or heat exchanger.

Auxiliary limit

Found on some furnaces near the blower. Protects against overheating if the blower fails.

Pressure switch problems

Symptoms: the inducer runs, but the igniter never glows, and the board flashes a "pressure switch open" code.

What usually causes it:

  • A clogged condensate trap or drain on high-efficiency furnaces. Water backs up and blocks the pressure port. This is the number one cause in Schertz attic furnaces.
  • Cracked, kinked or water-filled tubing between the switch and the inducer
  • A blocked vent or intake pipe: bird or wasp nests, debris, or a disconnected PVC joint
  • A weak inducer motor that can't build enough draft
  • A failed switch, which happens, but less often than the causes above

Limit switch problems

Symptoms: the furnace lights and heats, then shuts off mid-cycle while the blower keeps running, then restarts later. You may notice it short cycling.

What usually causes it:

  • A clogged filter. By far the most common cause, and worse during mountain cedar season. Check this first.
  • Closed or blocked supply vents and returns (furniture, rugs, closed doors to rooms with returns)
  • A dirty blower wheel or failing blower motor
  • Undersized or crushed ductwork, common with attic flex ducts
  • A weak switch that trips below its rated temperature

Repeated limit trips aren't harmless. Each one means the heat exchanger got hot enough to trigger a safety shutdown, and chronic overheating is a leading cause of cracked heat exchangers.

Never jumper or bypass a safety switch to get heat. It can cause overheating, flame rollout or carbon monoxide exposure. If a rollout switch has tripped, don't reset it repeatedly. Call a technician.

How we fix it

  1. Read the code and the history to see which switch is tripping and when.
  2. Measure draft with a manometer (pressure switch) or temperature rise and static pressure (limit switch).
  3. Find and fix the cause: clear traps, replace tubing, clear vents, clean the blower, correct airflow.
  4. Test the switch itself and replace it only if it's faulty, with the exact rated replacement.

Pressure and limit switch repair cost

Typical safety switch repair costs in SchertzParts and labor, Schertz / San Antonio area, 2026 estimates. You get an exact written price before work begins.
Item Typical cost Notes
Condensate trap / tubing clearing $120 – $300 Most common pressure-switch fix
Pressure switch replacement $150 – $450 Exact rated replacement
Limit or rollout switch replacement $150 – $400 After the cause is fixed
Vent pipe clearing or repair $150 – $500 Nests, debris, disconnected joints
FAQ

Pressure & Limit Switch Repair FAQs

Don't see your question? Call (210) 898-9282.

What does a pressure switch error mean on my furnace?

The furnace didn't confirm a safe exhaust draft, so it won't light. The cause is usually a blocked condensate trap, tubing or vent, or a weak inducer, and less often the switch itself.

Why does my furnace shut off and then come back on?

That pattern usually means the high limit switch is tripping from overheating. Start by replacing the filter and opening all vents. If it continues, call for service. See furnace keeps shutting off.

Can I reset a tripped rollout switch?

Some have a reset button, but a rollout trip means flames escaped the burner area, often from a blocked flue or a damaged heat exchanger. Have it inspected rather than resetting it.

Furnace down? Get your heat back today.

Licensed furnace repair in Schertz, TX, with a written price before work and 24/7 emergency service.

Call Now Free Estimate